Installing a cluster on Azure into an existing VNet

• You reviewed details about the OKD installation and update processes.

• You read the documentation on .

• You configured an Azure account to host the cluster and determined the tested and validated region to deploy the cluster to.

• If you use a firewall, you that your cluster requires access to.

• If the cloud identity and access management (IAM) APIs are not accessible in your environment, or if you do not want to store an administrator-level credential secret in the kube-system namespace, you can manually create and maintain IAM credentials.

About reusing a VNet for your OKD cluster

In OKD 4.8, you can deploy a cluster into an existing Azure Virtual Network (VNet) in Microsoft Azure. If you do, you must also use existing subnets within the VNet and routing rules.

By deploying OKD into an existing Azure VNet, you might be able to avoid service limit constraints in new accounts or more easily abide by the operational constraints that your company’s guidelines set. This is a good option to use if you cannot obtain the infrastructure creation permissions that are required to create the VNet.

When you deploy a cluster by using an existing VNet, you must perform additional network configuration before you install the cluster. In installer-provisioned infrastructure clusters, the installer usually creates the following components, but it does not create them when you install into an existing VNet:

• Subnets

• Route tables

• VNets

• Network Security Groups

If you use a custom VNet, you must correctly configure it and its subnets for the installation program and the cluster to use. The installation program cannot subdivide network ranges for the cluster to use, set route tables for the subnets, or set VNet options like DHCP, so you must do so before you install the cluster.

The cluster must be able to access the resource group that contains the existing VNet and subnets. While all of the resources that the cluster creates are placed in a separate resource group that it creates, some network resources are used from a separate group. Some cluster Operators must be able to access resources in both resource groups. For example, the Machine API controller attaches NICS for the virtual machines that it creates to subnets from the networking resource group.

Your VNet must meet the following characteristics:

• The VNet’s CIDR block must contain the Networking.MachineCIDR range, which is the IP address pool for cluster machines.

• The VNet and its subnets must belong to the same resource group, and the subnets must be configured to use Azure-assigned DHCP IP addresses instead of static IP addresses.

You must provide two subnets within your VNet, one for the control plane machines and one for the compute machines. Because Azure distributes machines in different availability zones within the region that you specify, your cluster will have high availability by default.

To ensure that the subnets that you provide are suitable, the installation program confirms the following data:

• All the specified subnets exist.

• There are two private subnets, one for the control plane machines and one for the compute machines.

• The subnet CIDRs belong to the machine CIDR that you specified. Machines are not provisioned in availability zones that you do not provide private subnets for. If required, the installation program creates public load balancers that manage the control plane and worker nodes, and Azure allocates a public IP address to them.

Network security group requirements

The network security groups for the subnets that host the compute and control plane machines require specific access to ensure that the cluster communication is correct. You must create rules to allow access to the required cluster communication ports.

Division of permissions

Starting with OKD 4.3, you do not need all of the permissions that are required for an installation program-provisioned infrastructure cluster to deploy a cluster. This change mimics the division of permissions that you might have at your company: some individuals can create different resources in your clouds than others. For example, you might be able to create application-specific items, like instances, storage, and load balancers, but not networking-related components such as VNets, subnet, or ingress rules.

The Azure credentials that you use when you create your cluster do not need the networking permissions that are required to make VNets and core networking components within the VNet, such as subnets, routing tables, internet gateways, NAT, and VPN. You still need permission to make the application resources that the machines within the cluster require, such as load balancers, security groups, storage accounts, and nodes.

Isolation between clusters

Because the cluster is unable to modify network security groups in an existing subnet, there is no way to isolate clusters from each other on the VNet.

Generating a key pair for cluster node SSH access

During an OKD installation, you can provide an SSH public key to the installation program. The key is passed to the Fedora CoreOS (FCOS) nodes through their Ignition config files and is used to authenticate SSH access to the nodes. The key is added to the ~/.ssh/authorized_keys list for the core user on each node, which enables password-less authentication.

After the key is passed to the nodes, you can use the key pair to SSH in to the FCOS nodes as the user core. To access the nodes through SSH, the private key identity must be managed by SSH for your local user.

If you want to SSH in to your cluster nodes to perform installation debugging or disaster recovery, you must provide the SSH public key during the installation process. The ./openshift-install gather command also requires the SSH public key to be in place on the cluster nodes.

Procedure

1. If you do not have an existing SSH key pair on your local machine to use for authentication onto your cluster nodes, create one. For example, on a computer that uses a Linux operating system, run the following command:

   1	Specify the path and file name, such as ~/.ssh/id_rsa, of the new SSH key. If you have an existing key pair, ensure your public key is in the your ~/.ssh directory.

   If you plan to install an OKD cluster that uses FIPS Validated / Modules in Process cryptographic libraries on the x86_64 architecture, do not create a key that uses the ed25519 algorithm. Instead, create a key that uses the rsa or ecdsa algorithm.

2. View the public SSH key:

   $ cat <path>/<file_name>.pub

   For example, run the following to view the ~/.ssh/id_rsa.pub public key:

   $ cat ~/.ssh/id_rsa.pub

3. Add the SSH private key identity to the SSH agent for your local user, if it has not already been added. SSH agent management of the key is required for password-less SSH authentication onto your cluster nodes, or if you want to use the ./openshift-install gather command.

   On some distributions, default SSH private key identities such as ~/.ssh/id_rsa and ~/.ssh/id_dsa are managed automatically.

   1. If the ssh-agent process is not already running for your local user, start it as a background task:

      $ eval "$(ssh-agent -s)"

      Example output

      Agent pid 31874

      If your cluster is in FIPS mode, only use FIPS-compliant algorithms to generate the SSH key. The key must be either RSA or ECDSA.

4. Add your SSH private key to the ssh-agent:

   $ ssh-add <path>/<file_name> (1)

   1	Specify the path and file name for your SSH private key, such as ~/.ssh/id_rsa

   Example output

   Identity added: /home/<you>/<path>/<file_name> (<computer_name>)

Next steps

• When you install OKD, provide the SSH public key to the installation program.

Before you install OKD, download the installation file on a local computer.

Prerequisites

• You have a computer that runs Linux or macOS, with 500 MB of local disk space

Procedure

1. Download installer from

   The installation program creates several files on the computer that you use to install your cluster. You must keep the installation program and the files that the installation program creates after you finish installing the cluster. Both files are required to delete the cluster.

   Deleting the files created by the installation program does not remove your cluster, even if the cluster failed during installation. To remove your cluster, complete the OKD uninstallation procedures for your specific cloud provider.

2. Extract the installation program. For example, on a computer that uses a Linux operating system, run the following command:

   $ tar xvf openshift-install-linux.tar.gz

3. From the Pull Secret page on the Red Hat OpenShift Cluster Manager site, download your installation pull secret. This pull secret allows you to authenticate with the services that are provided by the included authorities, including Quay.io, which serves the container images for OKD components.

   Using a pull secret from the Red Hat OpenShift Cluster Manager site is not required. You can use a pull secret for another private registry. Or, if you do not need the cluster to pull images from a private registry, you can use {"auths":{"fake":{"auth":"aWQ6cGFzcwo="}}} as the pull secret when prompted during the installation.

   If you do not use the pull secret from the Red Hat OpenShift Cluster Manager site:

   • Red Hat Operators are not available.

   • The Telemetry and Insights operators do not send data to Red Hat.

   • Content from the registry, such as image streams and Operators, are not available.

Creating the installation configuration file

You can customize the OKD cluster you install on Microsoft Azure.

Prerequisites

• Obtain the OKD installation program and the pull secret for your cluster.

• Obtain service principal permissions at the subscription level.

Procedure

1. Create the install-config.yaml file.

   1. Change to the directory that contains the installation program and run the following command:

      $ ./openshift-install create install-config --dir=<installation_directory> (1)

      Specify an empty directory. Some installation assets, like bootstrap X.509 certificates have short expiration intervals, so you must not reuse an installation directory. If you want to reuse individual files from another cluster installation, you can copy them into your directory. However, the file names for the installation assets might change between releases. Use caution when copying installation files from an earlier OKD version.

1. Modify the install-config.yaml file. You can find more information about the available parameters in the “Installation configuration parameters” section.

2. Back up the install-config.yaml file so that you can use it to install multiple clusters.

   The install-config.yaml file is consumed during the installation process. If you want to reuse the file, you must back it up now.

Before you deploy an OKD cluster, you provide parameter values to describe your account on the cloud platform that hosts your cluster and optionally customize your cluster’s platform. When you create the install-config.yaml installation configuration file, you provide values for the required parameters through the command line. If you customize your cluster, you can modify the install-config.yaml file to provide more details about the platform.

Required configuration parameters

Required installation configuration parameters are described in the following table:

Network configuration parameters

You can customize your installation configuration based on the requirements of your existing network infrastructure. For example, you can expand the IP address block for the cluster network or provide different IP address blocks than the defaults.

Only IPv4 addresses are supported.

networking:
  serviceNetwork:
   - 172.30.0.0/16

networking:
  machineNetwork:
  - cidr: 10.0.0.0/16

Optional configuration parameters

Optional installation configuration parameters are described in the following table:

sshKey:
  <key1>
  <key2>
  <key3>

Additional Azure configuration parameters

Additional Azure configuration parameters are described in the following table:

Sample customized install-config.yaml file for Azure

You can customize the install-config.yaml file to specify more details about your OKD cluster’s platform or modify the values of the required parameters.

apiVersion: v1
baseDomain: example.com (1)
controlPlane: (2)
  hyperthreading: Enabled  (3) (4)
  name: master
  platform:
    azure:
      osDisk:
        diskSizeGB: 1024 (5)
      type: Standard_D8s_v3
  replicas: 3
compute: (2)
- hyperthreading: Enabled (3)
  name: worker
  platform:
    azure:
      type: Standard_D2s_v3
      osDisk:
        diskSizeGB: 512 (5)
      zones: (6)
      - "1"
      - "2"
      - "3"
  replicas: 5
metadata:
  name: test-cluster (1)
networking:
  clusterNetwork:
  - cidr: 10.128.0.0/14
    hostPrefix: 23
  machineNetwork:
  - cidr: 10.0.0.0/16
  networkType: OVNKubernetes
  serviceNetwork:
  - 172.30.0.0/16
  azure:
    baseDomainResourceGroupName: resource_group (7)
    region: centralus (1)
    networkResourceGroupName: vnet_resource_group (9)
    virtualNetwork: vnet (10)
    controlPlaneSubnet: control_plane_subnet (11)
    computeSubnet: compute_subnet (12)
    outboundType: Loadbalancer
    cloudName: AzurePublicCloud
pullSecret: '{"auths": ...}' (1)
sshKey: ssh-ed25519 AAAA... (13)

Configuring the cluster-wide proxy during installation

Production environments can deny direct access to the internet and instead have an HTTP or HTTPS proxy available. You can configure a new OKD cluster to use a proxy by configuring the proxy settings in the install-config.yaml file.

Prerequisites

• You have an existing install-config.yaml file.

• You reviewed the sites that your cluster requires access to and determined whether any of them need to bypass the proxy. By default, all cluster egress traffic is proxied, including calls to hosting cloud provider APIs. You added sites to the Proxy object’s spec.noProxy field to bypass the proxy if necessary.

  The Proxy object status.noProxy field is populated with the values of the networking.machineNetwork[].cidr, networking.clusterNetwork[].cidr, and networking.serviceNetwork[] fields from your installation configuration. For installations on Amazon Web Services (AWS), Google Cloud Platform (GCP), Microsoft Azure, and Red Hat OpenStack Platform (RHOSP), the Proxy object status.noProxy field is also populated with the instance metadata endpoint (169.254.169.254).

• If your cluster is on AWS, you added the ec2.<region>.amazonaws.com, elasticloadbalancing.<region>.amazonaws.com, and s3.<region>.amazonaws.com endpoints to your VPC endpoint. These endpoints are required to complete requests from the nodes to the AWS EC2 API. Because the proxy works on the container level, not the node level, you must route these requests to the AWS EC2 API through the AWS private network. Adding the public IP address of the EC2 API to your allowlist in your proxy server is not sufficient.

Procedure

1. Edit your install-config.yaml file and add the proxy settings. For example:

   apiVersion: v1
   baseDomain: my.domain.com
   proxy:
     httpProxy: http://<username>:<pswd>@<ip>:<port> (1)
     httpsProxy: https://<username>:<pswd>@<ip>:<port> (2)
     noProxy: example.com (3)
   additionalTrustBundle: | (4)
       -----BEGIN CERTIFICATE-----
       <MY_TRUSTED_CA_CERT>
       -----END CERTIFICATE-----
   ...

   1	A proxy URL to use for creating HTTP connections outside the cluster. The URL scheme must be http. If you use an MITM transparent proxy network that does not require additional proxy configuration but requires additional CAs, you must not specify an httpProxy value.
   2	A proxy URL to use for creating HTTPS connections outside the cluster. If you use an MITM transparent proxy network that does not require additional proxy configuration but requires additional CAs, you must not specify an httpsProxy value.
   3	A comma-separated list of destination domain names, IP addresses, or other network CIDRs to exclude from proxying. Preface a domain with . to match subdomains only. For example, .y.com matches x.y.com, but not y.com. Use * to bypass the proxy for all destinations.
   4	If provided, the installation program generates a config map that is named user-ca-bundle in the openshift-config namespace that contains one or more additional CA certificates that are required for proxying HTTPS connections. The Cluster Network Operator then creates a trusted-ca-bundle config map that merges these contents with the Fedora CoreOS (FCOS) trust bundle, and this config map is referenced in the trustedCA field of the Proxy object. The additionalTrustBundle field is required unless the proxy’s identity certificate is signed by an authority from the FCOS trust bundle. If you use an MITM transparent proxy network that does not require additional proxy configuration but requires additional CAs, you must provide the MITM CA certificate.

   The installation program does not support the proxy readinessEndpoints field.

2. Save the file and reference it when installing OKD.

The installation program creates a cluster-wide proxy that is named cluster that uses the proxy settings in the provided install-config.yaml file. If no proxy settings are provided, a cluster Proxy object is still created, but it will have a nil spec.

Deploying the cluster

You can install OKD on a compatible cloud platform.

Prerequisites

• Configure an account with the cloud platform that hosts your cluster.

• Obtain the OKD installation program and the pull secret for your cluster.

Procedure

1. Change to the directory that contains the installation program and initialize the cluster deployment:

   $ ./openshift-install create cluster --dir=<installation_directory> \ (1)
       --log-level=info (2)

   1	For <installation_directory>, specify the location of your customized ./install-config.yaml file.
   2	To view different installation details, specify warn, debug, or error instead of info.

   If the cloud provider account that you configured on your host does not have sufficient permissions to deploy the cluster, the installation process stops, and the missing permissions are displayed.

   When the cluster deployment completes, directions for accessing your cluster, including a link to its web console and credentials for the kubeadmin user, display in your terminal.

   Example output

   ...
   INFO Install complete!
   INFO To access the cluster as the system:admin user when using 'oc', run 'export KUBECONFIG=/home/myuser/install_dir/auth/kubeconfig'
   INFO Access the OpenShift web-console here: https://console-openshift-console.apps.mycluster.example.com
   INFO Login to the console with user: "kubeadmin", and password: "4vYBz-Ee6gm-ymBZj-Wt5AL"
   INFO Time elapsed: 36m22s

   The cluster access and credential information also outputs to <installation_directory>/.openshift_install.log when an installation succeeds.

   The Ignition config files that the installation program generates contain certificates that expire after 24 hours, which are then renewed at that time. If the cluster is shut down before renewing the certificates and the cluster is later restarted after the 24 hours have elapsed, the cluster automatically recovers the expired certificates. The exception is that you must manually approve the pending node-bootstrapper certificate signing requests (CSRs) to recover kubelet certificates. See the documentation for Recovering from expired control plane certificates for more information.

   You must not delete the installation program or the files that the installation program creates. Both are required to delete the cluster.

You can install the OpenShift CLI (oc) to interact with OKD from a command-line interface. You can install oc on Linux, Windows, or macOS.

You can install the OpenShift CLI (oc) binary on Linux by using the following procedure.

Procedure

1. Navigate to https://mirror.openshift.com/pub/openshift-v4/clients/oc/latest/ and choose the folder for your operating system and architecture.

2. Download oc.tar.gz.

3. Unpack the archive:

   $ tar xvzf <file>

4. Place the oc binary in a directory that is on your PATH.

   To check your PATH, execute the following command:

After you install the OpenShift CLI, it is available using the oc command:

$ oc <command>

Installing the OpenShift CLI on Windows

You can install the OpenShift CLI (oc) binary on Windows by using the following procedure.

Procedure

1. Navigate to https://mirror.openshift.com/pub/openshift-v4/clients/oc/latest/ and choose the folder for your operating system and architecture.

2. Download oc.zip.

3. Unzip the archive with a ZIP program.

4. Move the oc binary to a directory that is on your PATH.

   To check your PATH, open the command prompt and execute the following command:

   C:\> path

After you install the OpenShift CLI, it is available using the oc command:

C:\> oc <command>

Installing the OpenShift CLI on macOS

You can install the OpenShift CLI (oc) binary on macOS by using the following procedure.

Procedure

1. Navigate to https://mirror.openshift.com/pub/openshift-v4/clients/oc/latest/ and choose the folder for your operating system and architecture.

2. Download oc.tar.gz.

3. Unpack and unzip the archive.

4. Move the oc binary to a directory on your PATH.

   To check your PATH, open a terminal and execute the following command:

   $ echo $PATH

After you install the OpenShift CLI, it is available using the oc command:

$ oc <command>

Logging in to the cluster by using the CLI

You can log in to your cluster as a default system user by exporting the cluster kubeconfig file. The kubeconfig file contains information about the cluster that is used by the CLI to connect a client to the correct cluster and API server. The file is specific to a cluster and is created during OKD installation.

Prerequisites

• You deployed an OKD cluster.

• You installed the oc CLI.

Procedure

1. Export the kubeadmin credentials:

   $ export KUBECONFIG=<installation_directory>/auth/kubeconfig (1)

   1	For <installation_directory>, specify the path to the directory that you stored the installation files in.

2. Verify you can run oc commands successfully using the exported configuration:

   $ oc whoami

   Example output

Additional resources

• See Accessing the web console for more details about accessing and understanding the OKD web console.

Additional resources

• See for more information about the Telemetry service

Next steps